Servo Turret - Indexer
1810 Amplifier / 1860
Controller Board
Three Purchase Options:
- NEW
(when available)
- REMANFACTURED, off the shelf exchange
-
REPAIR, best savings with fast turnaround
Specifications:
Part
Number
- PCB-0108 Amplifier and Control Board for Servo Turret and Indexer
- Remanufactured
- One Year Warranty
- Tested and
Warranty by ITS
Software Policy: We do not sell or distribute
Fadal copyrighted software. Boards such as the 1860 CPU board
requires Fadal copyrighted software. It is best to retain and
use your original Eproms and avoid introducing software
compatibility issues. Contact a Fadal authorized Eprom
supplier, they provide Eprom upgrade exchanges, usually for
free.
About the
Amplifier / Controller:
This board combination is used for the high speed Servo
Turret option on the Tool Changer and it is also used for the
original Fadal
Indexer. It's much more than an amplifier. It is a microprocessor
controlled amplifier! It consists of two parts; on one side is
the 1810 amplifier power section and on the other is the 1860
logic board (microprocessor based) which controls the functions
of the motor and the feedback devices. For the machine application; it's connected to the tool changer turret
for rotating to the next tool. For the
Indexer; the amplifier section and logic section are separately
mounted in the Indexer box.
True Knowledge and
Experience you can Trust:
Experience - Always Your
Best Choice:
Having
been involved in the original design and production of the CNC88 hardware and software, we truly understand these boards; to
the component level and the requirements for properly repairing
and testing of all the boards we offer. With over 18 years of
production testing and repairing CNC88 boards, there is
none better experienced or equipped than ITS.
Independent Technology Service Inc. (ITS), the original PCB
board house for Fadal, has been testing and repairing all
production boards, since 1991.
On your board, chances are you'll see the
stamp already on it!
Before You Buy - Ask how
the servo board was tested!
One simple question can save you a
lot of frustration, wasted time and money when servicing a
problematic machine. The common "repair" method today for others
selling boards is to put a used board in a machine and see if it
fails. It cannot be considered a "good board" just because the
control doesn't fault. Most of the time there is no history
of the board, no record of past performance (problems).
In fact, without proper testing, chances are you will be getting
other unknown board problems when installing used, untested boards; wasting
even more of your time and money!
Testing That Is
Unsurpassed!
We are the only
ones who can properly test and repair the CNC88 boards! It
requires component level testing to verify that each and every
component is performing to original specifications.
The Best And Only Way - In
Circuit and Functional Testing:
The testing of electric circuits to determine and locate any of the
following circuit conditions:
(1) an open circuit.
(2) a short circuit with another conductor in the same circuit.
(3) a ground, which is a short circuit between a conductor and ground.
(4) leakage (a high-resistance path across a portion of the circuit, to
another circuit, or to ground).
(5) a cross (a short circuit or leakage between conductors of different
circuits).
(6) a marginal or failed component(s).
The simple fact is that
proper circuit testing for complex systems requires extensive
automatic testing equipment to determine the failures defined
above as well as many other quantities required to insure the
board is working correctly.
Servo Board Replacement Options:
1- New or Remanufactured exchanges
are available for
immediate shipping, requires core exchange. A core refund
is issued when we receive the bad pcb board. The core
return board must be in a state that is repairable not damaged.
2- We will repair your board, for about 1/2 the cost of exchange
replacement! Rush repairs are available on most boards.
