Fadal Power / Relay Board
All Versions with the
latest revisions
Three Purchase Options:
- NEW (when available)
- REMANFACTURED, off the shelf exchange
-
REPAIR, best savings with fast turnaround
Specifications:
Part Number -
POWER DISTRIBUTION BOARDS
- PCB-1100-1B
- PCB-1100-2D
- Remanufactured
- One Year Warranty
- Tested and
Warranty by ITS
About the
1100 Power Distribution Boards:
Every machine uses two 1100 boards for controlling
various devices.
1) 1100-1 Board:
The Power Distribution and Relay PCB 1100-1 has inputs of
120VAC, 5VDC and the control signals. The control signals used
by the 1100-2 board are routed to another connector and go to
the 1100-2 board. The control signals from the Mill Interface
(1040) activate relays when required by pulling the control line
low or about zero volts. This board has the Emergency Stop
relays K1 & K2, high & low range, coolant pumps, Amplifier
control, M-functions and power to the pendant.
2) 1100-2 Board:
The Power Distribution and Relay PCB 1100-2 has inputs of
120VAC, 5VDC and the control signals. The control signals from
the Mill Interface (1040) and Spindle Controller (1010) activate
relays when required by pulling the control line low or about
zero volts. This board has the spindle forward & reverse
signals, ATC controls, Drawbar, Orientation and waylube.
True Knowledge and
Experience you can Trust:
Experience - Always Your
Best Choice:
Having
been involved in the original design and production of the Fadal
CNC hardware and software, we truly understand these boards; to
the component level and the requirements for properly repairing
and testing of all the boards we offer. With over 18 years of
production testing and repairing Fadals CNC boards, there is
none better experienced or equipped than ITS.
Independent Technology Service Inc. (ITS), the original PCB
board house for Fadal, has been testing and repairing production boards.
On your board, chances are you'll see the
stamp already on it!
Before You Buy - Ask how
the board was tested!
One simple question can save you a
lot of frustration, wasted time and money when servicing a
problematic machine. The common "repair" method today for others
selling boards is to put a used board in a machine and see if it
fails. It cannot be considered a "good board" just because the
control doesn't fault. Most of the time there is no history
of the board, no record of past performance (problems).
In fact, without proper testing, chances are you will be getting
other unknown board problems when installing used, untested boards; wasting
even more of your time and money!
Testing That Is
Unsurpassed!
We are the only
ones who can properly test and repair CNC88 boards! It
requires component level testing to verify that each and every
component is performing to original specifications.
The Best And Only Way - In
Circuit and Functional Testing:
The testing of electric circuits to determine and locate any of the
following circuit conditions:
(1) an open circuit.
(2) a short circuit with another conductor in the same circuit.
(3) a ground, which is a short circuit between a conductor and ground.
(4) leakage (a high-resistance path across a portion of the circuit, to
another circuit, or to ground).
(5) a cross (a short circuit or leakage between conductors of different
circuits).
(6) a marginal or failed component(s).
The simple fact is that
proper circuit testing for complex systems requires extensive
automatic testing equipment to determine the failures defined
above as well as many other quantities required to insure the
board is working correctly.
CNC Board Replacement Options:
1- New or Remanufactured exchanges
are available for
immediate shipping, requires core exchange. A core refund
is issued when we receive the bad pcb board. The core
return board must be in a state that is repairable not damaged.
2- We will repair your board, for about 1/2 the cost of exchange
replacement! Rush repairs are available on most boards.
